Waveform Options



shm_waveforms.md

The traditional waveform monitor is useful in measuring the brightness, or luminance component, of a video signal. In Premiere Pro, the waveform monitors can also display chrominance information. The waveform monitor works something like a graph. The horizontal axis of the graph corresponds to the video image from left to right. Creating SHM waveforms with irun. GitHub Gist: instantly share code, notes, and snippets.

The previous one and reset the rest of power analysis options to default values. Option -cycleaccurateclock and -cycleaccu- ratecyclecount are exclusive with option -waveforminterval in this command. The following is the table of options supported in each power analysis mode. When creating a waveform image, specifies the start time, in seconds.-end, -e (default: 0) When creating a waveform image, specifies the end time, in seconds. Note: this option cannot be used if the -zoom option is specified.-width, -w (default: 800) When creating a.

commented Jun 17, 2013

NB: for shm the -all option does not cover memories, as well as -all these can also be used to control what is captured:

commented Apr 5, 2019

Found some shm_probe() arguments somewhere on the web, might be useful here:
Shm_probe(');
A: all nodes, including inputs, outputs and inouts, of the specified scope
S: inputs, outputs and inouts of the specified scope, and in all instantiations below it, except inside library cells.
C: inputs, outputs and inouts of the specifed scope, and in all instantiations below it, including those inside library cells.
AS: all nodes, including inputs, outputs and inouts, of the specified scope, and in all instantiations below it, except inside library cells.
AC: all nodes, including inputs outputs and inouts, in the specified scope and in all instantiations below it, even inside library cells.

commented Dec 3, 2019

To add Memories to the shm_probe command add 'M' to the end of the option ie.

Waveform Options Explained

Sign up for freeto join this conversation on GitHub. Already have an account? Sign in to comment

For certain types of musical sequences, the Sequence Editor can display a waveform of the audio at the top of each track. This can be useful for visually matching up timings and events to the sound. The Waveform Display supports a wide range of media types, including video media. However, not all types of media or media containers are supported. Also, the Waveform Display may not be able to be used with very large media files.

In addition to the waveform itself, a vertical highlight bar is displayed at the current time that your mouse is pointing at.

•Viewing the waveform

•Scaling up and down

•Changing the display type

•Changing the colors

A musical sequence with an audio waveform displayed

Viewing the Waveform

To view the waveform for a media file, make sure that 'Wave Form' on the View menu is set to either 'Full Height' or 'Half Height'. To hide the waveform, set it to 'Off'.

'Full Height' or 'Half Height' determines the size of the whole display. This should not be confused with scaling up and down, which will keep the size of the display the same, but vary the size of the graph within the display.

The View Wave Form button on the Standard Toolbar can be used to toggle between 'Off' and whichever of 'Full Height' and 'Half Height' was last selected.

Additionally, 'View Wave Form by Default' in the Display Preferences dialog can be used to control whether or not a waveform will automatically be displayed whenever a musical sequence (of an appropriate type) is opened or created.

Scaling Up and Down

When displaying a waveform, the Sequence Editor tries to automatically scale the graph's vertical size so that a lot of the wave is displayed. There may be occasional spots where the wave goes past the top of the display - corresponding to very loud spots in the audio - but these should be infrequent.

However, you may want to zoom in or out. To do this, click on the 'Scale Up' or 'Scale Down' buttons to the left of the waveform display. Note that these buttons are visible if and only if the channel buttons are visible.

If you do zoom in or out, the Sequence Editor will remember your zoom settings for this particular sequence for whenever you open it in the future.

This should not be confused with the 'Full Height' and 'Half Height' options, which change the size of the entire display, rather than the size of the graph on the display.

The scaling buttons

A portion of a waveform, scaled up

The same waveform, scaled down

Changing the Display Type

By default, the waveform display is centered about a line corresponding to zero volume. Loud portions of the song will extend both far above and far below the center. This is known as 'full mode'.

A portion of a waveform, in full mode

Two other modes are also supported: 'fold mode' and 'top mode'.

'Fold mode' shows zero volume at the bottom of the display, and above it shows whichever half of full mode would be larger, as if the two halves were folded at the center and lain on top of each other. It is then stretched vertically so that the full size of the display is used.

Elliott Wave Options

The same waveform, in fold mode

'Top mode' is similar to fold mode, except that only those portions of the display which would have been above the center in full mode are shown.

The same waveform, in top mode

To change between the modes, right-click on the wave form, and choose the desired mode from the popup menu.

Second

The waveform popup menu, with top mode selected

When you choose a mode, the Sequence Editor automatically saves it, and uses it as the default mode in the future.

Changing the Colors

The colors used to display the waveform can be changed via the Wave Colors dialog, which can be opened by right-clicking on the waveform and selecting 'Change Colors' from the popup menu:

'Change Colors' on the waveform popup menu

The Wave Colors dialog

Three different colors can be set: 'Foreground' is the color of the wave itself; 'background' is the field that it is drawn upon; 'highlight' is the vertical bar showing the position of the mouse.

Options Permanent Wave Option 2

The colored buttons on the left can be used to set each of these three colors, and the display on the right shows how a sample waveform would look using these colors.

Elliott Wave Options Rob Roy

The Sequence Editor will remember the colors that you chose, so that other waveforms will automatically be displayed using those colors.

The Wave Colors dialog, with different colors chosen